HARDWIRE HT-6POLYCHROMATIC TUNEROWNER’S MANUAL
64. LED Display Matrix - This area features 90 LEDs in six rows that are used to display both polyphonic and single note tuning states of your instru
77. Mode Button - When the tuner is on, this button is used to select between the two Display Modes: Normal and Strobe. 8. Note Display - This serie
812. Output Jack - Connect this output to your amp or the input of the next pedal in the signal chain. The signal from this output connection will b
9Tuner Display ModesPressing the Tuning Button multiple times toggles between the below modes:• Guitar Standard (EADGBE) – This mode is indicated whe
10Selecting A Tuner ReferenceThe HT-6 Tuner has multiple tuning references to select from: • A=436 - 445 (including A=440 standard tuning)• A=A♭*•
11To set the HT-6 Tuner’s tuning reference, follow these steps:1. Press the Foot Switch to turn on the tuner. 2. Press and hold the Tuning Button fo
12Polyphonic TuningThe main benefit of the HT-6 Tuner is the ability to see and tune all six strings simultaneously. To do this, follow these steps:1.
133. If a string is in tune, the three center LEDs (yellow-blue-yellow) will light on the corresponding string’s row. If a string is flat, LEDs to th
14Display Modes (Single Note Mode Only)The HT-6 Tuner has two different tuning display modes when using Single Note tuning mode: Normal and Strobe. No
15the LEDs will be in motion to the right meaning the note needs to be tuned down. The speed of the motion indicates how far out of tune the note is.
DECLARATION OF CONFORMITYManufacturer’s Name: Harman Signal Processing Manufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USAdecla
16Single Note Tuning - Normal ModeTo tune your guitar or bass, one string at a time, follow these steps:1. Press the Foot Switch to turn the tuner on
174. If the displayed note’s pitch is sharp, LEDs to the right of the center blue LED will be lit. A set of red LEDs on the right side of the LED Dis
18SINGLE NOTE TUNING TIP: For the best results when tuning individual strings, try to mute any strings that are not being tuned. TROUBLESHOOTING TIP:
19Single Note Tuning - Strobe ModeTo tune your guitar or bass, one string at a time, follow these steps:1. Press the Foot Switch to turn the tuner on
20the LED movement will slow down. When the LED array stops moving, the note is in tune.4. Continue to tune the rest of your strings in the same fash
21Setting the Fret Offset The Fret Offset mode works by setting the expected notes for each string to be a fixed offset (in semitones) from a standard
223. Strum your guitar while holding down the Foot Switch. The offset will be detected and will show in the Note Display (-6 to 6).4. Releasing the
23Setting The Fret Offset Manually1. Hold down the Foot Switch until the LED Matrix Display shows “FRET” and the Note Display shows the current offse
24Using the HT-6 to Power Other PedalsThe HT-6 Tuner has the ability to power other pedals in your pedalboard using an optional multi pedal power cabl
25Battery OperationIn the event that battery power is completely depleted, DigiTech HardWire pedals automatically switch into bypass. This eliminates
WARNINGFor your protection, read the following:Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warni
26into place over the depressed pin. Release the pin. When the Foot Switch is properly fastened, both release pins are flush with the outer side of th
27Low Battery MessageWhen using the HT-6 PolyChromatic Tuner with a battery, the display will flash BATT approximately 30 minutes before the end of th
28Performance AccessoriesThe performance accessories make integrating a HardWire pedal into any pedal board a snap. The following accessories are incl
29Hook-and-loop Pedalboard PadTo attach the Pedalboard Pad, do the following:1. Peel off the existing rubber skid pad from the bottom of the pedal.2.
30Foot Switch Glow StickerTo attach the Foot Switch Glow Sticker, do the following:1. Peel the adhesive backing from the Foot Switch Glow Sticker.2.
31SpecificationsControls: On/Off Foot Switch, Mode Button, and Tuning ButtonJacks: Input, OutputTuning Range: 27.5 Hz - 1320 HzTuning Accuracy:
8760 South Sandy ParkwaySandy, Utah 84070PH (801) 566-8800FAX (801) 566-7005 DigiTech® and HardWire® are registered trademarks of HarmanDesigned in th
WARRANTY: We at DigiTech® are very proud of our products and back-up each one we sell with the following warranty:1. Please register online at www.d
1IntroductionMore than a remarkable achievement, DigiTech’s HardWire® series represents a collection of significant improvements in guitar effects ped
2Features• Polyphonic Tuning (tune all strings at once)• Single Note Tuning (accurately tune single strings for any note)• Automatically detects be
3Amplifier In-Line SetupCustom9VDC Out 9VDC In USBGuitar BassModeTuningEBGDAECGDAEBHarman PowerSupply (optional)orNOTE: Use unbalanced mono instrument
4Pedal InterfaceCustom9VDC Out9VDC In USBGuitar BassModeTuningEBGDAECGDAEB1413121110987654321
5What Does This Do?1. DC Power Output - This jack is a power output for providing additional power to other pedals. Connect the HardWire HV-5 five pe
Comments to this Manuals